Atlas Support - Natural

Atlas Support is the next generation in PVA water-soluble support materials for FFF/FDM 3D printing. Atlas Support is the result of extensive research to PVA improvement which has resulted in an unique formulation where numerous PVA grades have been blended into one superior water soluble support material with improved thermal stability. 
Atlas Support has good bonding to a wide variety of materials – such as PLA, ABS, PETG, ASA, HIPS, et cetera – and is much less sensitive to degradation by humidity.

Unique features

• Excellent water solubility

• • Excellent support material for complex dual extrusion prints!

• Improved thermal stability

• • Much lesser risk of clogged nozzles caused by deteriorating/crystalizing material in (too) hot nozzle

• Good bonding to various (thermo)plastics

• Odourless processing

• Biodegradable once dissolved in water

General printing guidelines *

*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.

*) Do not exceed a printing temperature of 225˚C, because then PVA crystallizes quickly and it will no longer flow and/or dissolve in water. Printing with PVA materials does require a certain level of 3D printing expertise as PVA cannot stay too long in the hot secondary/support nozzle and needs to flow and by that needs expert tweaking to find the optimal “waiting temperature” for the material not to deteriorate/crystalizing in the hot secondary/support nozzle when not being printed.

Filament length

Formfutura PVA Support matrix

Below overview is meant to give guidance on which of our PVA based support materials – AquaSolve PVA, Atlas Support, and Helios Support – is advised as support material in combination with various Formfutura filaments that can be used as primary building material. 

Please do note that below overview is purely meant as general guidance and advice based on our in-house expertise and experience and that it is not to be seen as a fixed principle or rule. There are numerous factors that determine the best fitting PVA support with a primary building material and it actually varies per 3D printer. Below overview can according to our state of knowledge be used as guidance for the fast majority of 3D printers.

 EasyFil PLA / ReForm rPLA / Premium PLA

*) Max thermal stability tested up to 256 seconds with no flow.

*) Needed thermal stability increases with ‘build material’ temperature.

*) Interface layer speeds are guidelines to start testing. Speeds can improve!

 HDglass / ReForm rPET

 EasyFil ABS / Premium ABS / ClearScent ABS / TitanX / ReForm rTitan / ApolloX / Crystal Flex / 

Volcano PLA / Python Flex

General guidance for printing with PVA support materials

Printing with PVA in general isn’t plug and play and does require a fair amount of 3D printing expertise as there isn’t a generic one-size-fits all setting for dual extrusion printing with PVA materials. The optimal PVA settings can even vary between the same models of 3D printers. 

One of the most common challenges is to establish a good bond between the PVA support material and the primary building  material. Below parameters are of utmost importance to establish a good adherence.

• Verify the extrusion distance between the printed object and the PVA support.

• • The default setting in most slicer software is often set at a distance of 0.1mm or 0.2mm, which works well for break-away support, but not for PVA support.

  • For PVA support materials the extrusion distance must be set to 0.0mm as both materials must really come into contact with each other.

• The printing (nozzle) temperature is extremely important and it is advised to measure the actual temperature of the nozzle and to compare this temperature with the temperature set in the print settings.

• • If the actual temperature of the nozzle is for instance 10° C lower than the temperature in the print settings it might very well be that the layer of PVA support material is not flowing optimally into the layer of the primary building material. It is often seen that the actually nozzle temperature varies from the print temperature set in the slicing software.

• Verify if the nozzles of your printer are properly leveled and have exactly the same height, so that there is no “height difference” when layering the PVA support material on top of the primary building material.

• • In order to verify this it is recommended to 3D print a 5cm x 1cm rod and to print every 1 to 2 layers with the left nozzle and the following 1 to 2 layers with the right nozzle and to repeat this process multiple times. If you notice a non-perfect layering then the nozzles aren’t properly leveled. This process can be done with PLA for instance.

Product export information

Compliance *

This filament is compliant to below listed directives and regulations.

• RoHS directive 2011/65/EC

• REACH directive 1907/2006/EC 

*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.