Close
(0) Кошница
Няма продукти в кошницата.
Категории
    Filters
    Настройки
    Търси
    Производител: ColorFABB

    GLOWFILL

    93,96 лв.
    This filament will literally make your work shine! During the day it’s a beautiful creamy color which prints to a perfect smooth finish. In the dark your prints will start to glow like you would not believe. A special highly concentrated phosphorescent pigment is matched with our PLA/PHA compound, so it’ll print just like our other PLA/PHA 3d printing filament. So charge up those 3d prints for some glow in the dark fun!
    *
    *
    Наличност: Please select required attribute(s)

    This filament will literally make your work shine! During the day it’s a beautiful creamy color which prints to a perfect smooth finish. In the dark your prints will start to glow like you would not believe. A special highly concentrated phosphorescent pigment is matched with our PLA/PHA compound, so it’ll print just like our other PLA/PHA 3d printing filament. So charge up those 3d prints for some glow in the dark fun!

    Warning: Printing a lot with glowFill can cause wear to standard brass nozzles. We would recommend users to use more wear resistant nozzles such as hardened steel or ruby tipped nozzles when printing a lot of glowFill.

    Adviced 3d printing temperature:

    195-220C*

    Adviced 3d print speed:

    40 - 100 mm/s

    Advised Heated bed (if you have one, not strictly necessary)

    50-60C

     

    TIP! For a better and longer lasting glow time print your models with 100% infill and charge up your models with some high power lights, or just let them enjoy the sunlight for a bit.

     General Tips

    Build platform

    Our PLA/PHA compound performs well on both heated and non-heated build platforms. For those users printing on a cold build platform we advise applying masking tape to the build area. The rough surface of the tape will provide enough adhesion for the first layer to stick and print almost without any warping. 

    Users using heated build platforms have quite a few options these days. The usual suspects are glass and aluminum build plates. For directly printing on glass or aluminum we advice user to apply glue-stick. A very thin layer will be sufficient to keep your print nicely in place. Another method is dissolving wood glue in water, you the consistency of the substance can be quite thin, a bit like milk. By applying just a few drops and smearing this out before you start heating the built plate will create a very thing layer which holds the woodFill down very well. If applying this method, be careful that you don’t get your electronics wet.

    Another method that works well with colorFabb woodFill is polyimide tape, or Kapton tape. This tape is available as a very narrow strip or very wide strips which allow you to cover the build plate in one go. When the tape is applied correctly it can last for months.

    TIP! Take your time leveling the bed and adjusting the the gap between 3d printer nozzle and build plate. A perfect first layer will is very important, especially for 3d prints with a large bottom layer. Having the nozzle set to close to the build plate will cause a pressure build up and as a result back flow in most hot ends.  

    TIP! PLA/PHA has very minimal warping tendencies, however if your printing parts which take up the maximum of you buildspace you might see some warping. If it’s very important that your part is perfectly flat than we suggest to turn down the fan that is cooling your part. This allows the material to slowly get rid of heat without warping. After a few centimeters you can turn on the cooling if the part needs it.

    Material:

    colorFabb glowFill - PLA/PHA + concentrated phosphorescent pigment

    Diameter Tolerance:

    ± 0.05 mm

    Density:

    1.210-1.430 g·cm-3

    Glass Transition Temperature

    55C

    Продуктови спецификации
    Filament Material PLA
    Filament Diameter 1.75/2.85 mm
    Цвят
     
    Тегло 750 g
    Nozzle size ≥ 0.15mm
    Print temp ± 195 - 220° C
    Heat bed ± 50 - 60° C
    Layer height ≥ 0.1mm
    Print speed 40 - 100 mm/s
    Fan speed 50-100%
    Flow rate ± 100%
    Retraction Yes ± 5 mm
    Experience level Beginner
    Напиши отзив
    • Може да оставите отзив за продукт само след като го закупите.
    • Само регистрирани потребители могат да пишат отзиви
    *
    *
    • Лошо
    • Отлично
    *
    *
    *

    This filament will literally make your work shine! During the day it’s a beautiful creamy color which prints to a perfect smooth finish. In the dark your prints will start to glow like you would not believe. A special highly concentrated phosphorescent pigment is matched with our PLA/PHA compound, so it’ll print just like our other PLA/PHA 3d printing filament. So charge up those 3d prints for some glow in the dark fun!

    Warning: Printing a lot with glowFill can cause wear to standard brass nozzles. We would recommend users to use more wear resistant nozzles such as hardened steel or ruby tipped nozzles when printing a lot of glowFill.

    Adviced 3d printing temperature:

    195-220C*

    Adviced 3d print speed:

    40 - 100 mm/s

    Advised Heated bed (if you have one, not strictly necessary)

    50-60C

     

    TIP! For a better and longer lasting glow time print your models with 100% infill and charge up your models with some high power lights, or just let them enjoy the sunlight for a bit.

     General Tips

    Build platform

    Our PLA/PHA compound performs well on both heated and non-heated build platforms. For those users printing on a cold build platform we advise applying masking tape to the build area. The rough surface of the tape will provide enough adhesion for the first layer to stick and print almost without any warping. 

    Users using heated build platforms have quite a few options these days. The usual suspects are glass and aluminum build plates. For directly printing on glass or aluminum we advice user to apply glue-stick. A very thin layer will be sufficient to keep your print nicely in place. Another method is dissolving wood glue in water, you the consistency of the substance can be quite thin, a bit like milk. By applying just a few drops and smearing this out before you start heating the built plate will create a very thing layer which holds the woodFill down very well. If applying this method, be careful that you don’t get your electronics wet.

    Another method that works well with colorFabb woodFill is polyimide tape, or Kapton tape. This tape is available as a very narrow strip or very wide strips which allow you to cover the build plate in one go. When the tape is applied correctly it can last for months.

    TIP! Take your time leveling the bed and adjusting the the gap between 3d printer nozzle and build plate. A perfect first layer will is very important, especially for 3d prints with a large bottom layer. Having the nozzle set to close to the build plate will cause a pressure build up and as a result back flow in most hot ends.  

    TIP! PLA/PHA has very minimal warping tendencies, however if your printing parts which take up the maximum of you buildspace you might see some warping. If it’s very important that your part is perfectly flat than we suggest to turn down the fan that is cooling your part. This allows the material to slowly get rid of heat without warping. After a few centimeters you can turn on the cooling if the part needs it.

    Material:

    colorFabb glowFill - PLA/PHA + concentrated phosphorescent pigment

    Diameter Tolerance:

    ± 0.05 mm

    Density:

    1.210-1.430 g·cm-3

    Glass Transition Temperature

    55C

    Продуктови спецификации
    Filament Material PLA
    Filament Diameter 1.75/2.85 mm
    Цвят
     
    Тегло 750 g
    Nozzle size ≥ 0.15mm
    Print temp ± 195 - 220° C
    Heat bed ± 50 - 60° C
    Layer height ≥ 0.1mm
    Print speed 40 - 100 mm/s
    Fan speed 50-100%
    Flow rate ± 100%
    Retraction Yes ± 5 mm
    Experience level Beginner