Close
(0) Кошница
Няма продукти в кошницата.
Категории
    Filters
    Настройки
    Търси
    Производител: ColorFABB

    IGUS IGLIDUR I180-BL

    179,13 лв.
    Components made of igus® Tribo-Filament are up to 50 times more wear-resistant than standard materials for 3D printing and therefore have an extremely long service life. Due to their excellent tribological properties, they are suited for 3D printing of replacement parts, for example bearings, drive nuts, gears and other wear parts. The igus® Tribo-Filaments can be processed on 3D printers that are based on the fused-deposition-modelling method (FDM/FFF) and that allow the nozzle temperature to be set as required.
    *
    *
    Наличност: Please select required attribute(s)

    Components made of igus® Tribo-Filament are up to 50 times more wear-resistant than standard materials for 3D printing and therefore have an extremely long service life. Due to their excellent tribological
    properties, they are suited for 3D printing of replacement parts, for example bearings, drive nuts, gears and other wear parts. The igus® Tribo-Filaments can be processed on 3D printers that are based on the fused-deposition-modelling method (FDM/FFF) and that allow the nozzle temperature to be set as required.  
     
    Typical application areas

    • Special machine construction
    • Jig construction
    • Complex wear parts

    Dimensions

    filament diameter: 1.75 mm / 2.85 mm

    Outer diameter spool: 205 mm

    Inner diameter spool: 55 mm

    Spool width: 55 mm


    General properties

    Colour: white

    Material suitable for: Beginner

    Max. moisture absorption (at 23 °C/73 °F, 50% r.h.): 0.3 Wt.-%, test method DIN 53495

    Max. water absorption: 0.9 Wt.-%

    Net weight: 250 g / 750 g

    Coefficient of sliding friction, dynamic, against Cf53 steel: 0.24

    Coefficient of sliding friction, dynamic, against 304 stainless steel: 0.17

    pv value, max. (dry): 0.23 MPa ⋅ m/s

    Flexural strength: 46 / 33 MPa


    Physical and thermal properties

    Max. long-term application temperature: 80 °C

    Max. short-term application temperature: 90 °C

    Lower application temperature: -40 °C

    Thermal expansion coefficient (at 23°C/73°F): 9 K-1 ⋅ 10-5, test method DIN 53752

    Heat conductivity: 0.23 W/(m ⋅ K), test method ASTM C 177

    Pressure load: 59 MPa

    Max. recommended surface pressure (at +20 °C/68 °F): 30 MPa


    Requirements

    Mould-free according to DIN EN ISA 846 Procedure A: No


    Processing instructions

    Nozzle temperature (min.): 250 °C

    Nozzle temperature (max.): 260 °C

    Bed temperature (min.): 90 °C

    Bed temperature (max.): 110 °C

    Recommended adhesion: igus® adhesive film

    Construction space: Closed installation space necessary

    Component cooling: A component cooling is not necessary, with cooling switched on it is also possible to print

    Продуктови спецификации
    Filament Material Monofilament
    Filament Diameter 1.75/2.85 mm
    Цвят
     
    Тегло 750 g
    Nozzle size ≥ 0.15mm
    Print temp ± 250 - 260° C *
    Heat bed ± 90 - 110° C
    Layer height ≥ 0.1mm
    Print speed 40 - 70 mm/s
    Fan speed 50-100%
    Flow rate ± 100%
    Retraction Yes ± 5 mm
    Experience level Beginner
    Напиши отзив
    • Може да оставите отзив за продукт само след като го закупите.
    • Само регистрирани потребители могат да пишат отзиви
    *
    *
    • Лошо
    • Отлично
    *
    *
    *

    Components made of igus® Tribo-Filament are up to 50 times more wear-resistant than standard materials for 3D printing and therefore have an extremely long service life. Due to their excellent tribological
    properties, they are suited for 3D printing of replacement parts, for example bearings, drive nuts, gears and other wear parts. The igus® Tribo-Filaments can be processed on 3D printers that are based on the fused-deposition-modelling method (FDM/FFF) and that allow the nozzle temperature to be set as required.  
     
    Typical application areas

    • Special machine construction
    • Jig construction
    • Complex wear parts

    Dimensions

    filament diameter: 1.75 mm / 2.85 mm

    Outer diameter spool: 205 mm

    Inner diameter spool: 55 mm

    Spool width: 55 mm


    General properties

    Colour: white

    Material suitable for: Beginner

    Max. moisture absorption (at 23 °C/73 °F, 50% r.h.): 0.3 Wt.-%, test method DIN 53495

    Max. water absorption: 0.9 Wt.-%

    Net weight: 250 g / 750 g

    Coefficient of sliding friction, dynamic, against Cf53 steel: 0.24

    Coefficient of sliding friction, dynamic, against 304 stainless steel: 0.17

    pv value, max. (dry): 0.23 MPa ⋅ m/s

    Flexural strength: 46 / 33 MPa


    Physical and thermal properties

    Max. long-term application temperature: 80 °C

    Max. short-term application temperature: 90 °C

    Lower application temperature: -40 °C

    Thermal expansion coefficient (at 23°C/73°F): 9 K-1 ⋅ 10-5, test method DIN 53752

    Heat conductivity: 0.23 W/(m ⋅ K), test method ASTM C 177

    Pressure load: 59 MPa

    Max. recommended surface pressure (at +20 °C/68 °F): 30 MPa


    Requirements

    Mould-free according to DIN EN ISA 846 Procedure A: No


    Processing instructions

    Nozzle temperature (min.): 250 °C

    Nozzle temperature (max.): 260 °C

    Bed temperature (min.): 90 °C

    Bed temperature (max.): 110 °C

    Recommended adhesion: igus® adhesive film

    Construction space: Closed installation space necessary

    Component cooling: A component cooling is not necessary, with cooling switched on it is also possible to print

    Продуктови спецификации
    Filament Material Monofilament
    Filament Diameter 1.75/2.85 mm
    Цвят
     
    Тегло 750 g
    Nozzle size ≥ 0.15mm
    Print temp ± 250 - 260° C *
    Heat bed ± 90 - 110° C
    Layer height ≥ 0.1mm
    Print speed 40 - 70 mm/s
    Fan speed 50-100%
    Flow rate ± 100%
    Retraction Yes ± 5 mm
    Experience level Beginner